CO2 Glass Laser Tube 80W~150W for Laser Engraving and Cutting Machine

【SPECIAL COATING TECHNOLOGY】: This CO2 laser tube adopt inner discharge tube coated with nanogold catalyst technology, power is 10% improved, and service life is 20% longer than ordinary laser tube,better chooice for the people who has heavy workload and long working hours
【EASY INSTALLATION】: The wire on positive pole and negative pole had been connected in advance,just connect to the wire on the machine and cover with insulating tape will be ok
【APPLICATION】: This co2 laser tube compatible with all the co2 laser engraving and cutting machine that used laser tube as power,but please make sure your machine's installation space,like the diameter and length,all should be a little bigger than laser tube's size
【STABLE OUTPUT】: Single mode output mode, fine spot, strong penetrating power, no change in long-term use spot mode
【UNIQUE TECHNOLOGY】: With excellent sealed-off technology to divide air and prevent inside gas diffusion,the laser tube will be more stable and efficient.About the installation of laser tube,here is a video for your reference : https://youtu.be/mbwYveQZPZ8.

1. Mechanical parts (rails, etc.): There is no specific time limit for the lubrication of the mechanical parts (reasonable maintenance according to the use of the machine). If engraving and cutting materials what are corrosive or easy to produce dust, it is recommended to lubricate the parts after each use of the machine. If engraving and cutting the wood materials, the parts can be lubricated every 2 weeks (apply lubricant with linen, avoid Direct contact by hands, normal car lubricants can be used).

2. Lens: If engraving and cutting materials what are corrosive or easy to produce dust, Clean the lens after each use of the machine. If engraving and cutting the wood materials, the lens can be clean every 2 weeks. Please clean it with cotton swab and stick alcohol. When wiping the lens, pay attention to check if there are any scratches on the lens or if the reflective film falls off. (Regularly Cleaning)

3. Laser tube: The laser tube cooling water should be enough, at least 15 liters of water, keep the water cold and cycle it often. Change water every 2 weeks in Summer (Water temperature should not exceed 30 degrees in summer, can put ice in the water to cool down); Change water every 1 month in Winter (be careful not to let the water freeze in winter); When the machine power is high, need to keep the water clean. Before the machine starts working, be sure to Check whether the laser tube through the water normally, otherwise the laser tube will be damaged.
Our products are high-tech, please exercise caution when using it and properly maintain the equipment to allow it to function properly. We have some advice for you.

1. Do not open the sculptor back cover and change the structure inside the machine on your own.

2. Do not allow the device to vibrate violently.

3. Do not allow water to enter the equipment or use the environment too wet.

4. When wiping the lenses, gently wipe them with waterless ethanol or acetone.

5. In winter, please keep the indoor temperature above 5°C, do not let the water freeze, prevent freezing laser tube.

6. Under normal operation, the laser tube should keep the water circulating.

7. Normal use voltage 220V, 50Hz, use pure water.

8. The ground line must be in good contact.

9. Do not adjust the light path if you are not a professional.

10. For additional precautions, please refer to the product description and the teaching CD-ROM.

Under normal operation, the laser machine warranty time of one year, supplies warranty for three months, the whole machine life-long to provide paid services.

supplies: Laser tubes, reflective lenses, focused lenses
1. Keep the cooling water sufficient and usually, the water temperature is controlled below 30 degrees Celsius, and the temperature difference with the room does not exceed 5 degrees Celsius, to prevent the laser tube body or window mirror from condensation due to excessive water temperature difference. If the phenomenon of condensation occurs, the condensation part can be wiped clean (wipe clean before the power must be turned off), and then adjust the cooling water temperature to the appropriate temperature, and then restart the work.
The laser inlet and outlet water should be low into the high principle, the laser inlet and outlet water pipe should be far away from the laser tube body (especially the light outlet tube body), the tube body outlet vertical up, no bubbles in the tube. (Laser tube into the water outlet can not be tilted, due to installation problems lead to fried tube, our company does not carry out warranty.)
2. Keep the window mirror lens clean and free of pollution. Regularly or irregularly with bamboo swabs with anhydrous ethanol (alcohol) on the laser window mirror pollutants to clean. (Pay attention to the strength when cleaning the window mirror to avoid the lens being scrubbed)
3. Pay attention to keep the high voltage end clean and dry, regularly clean the dust around the high voltage electrode, or isolate the electrode with plastic film to avoid the high voltage end from firing.

Translated with www.DeepL.com/Translator (free version)

$914.00

Quantity

CO2 Glass Laser Tube 80W~150W for Laser Engraving and Cutting Machine

Machine maintenance

Warranty policy

Laser tube precautions